Volvo 2003T Manual de Serviço Página 15

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 48
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 14
13
Injected quantity .......................................................... 25±1,5 mm
3
/stroke at 40±5°C (104°F ±10.6°F)
and at 1500 rpm pump revs
Governor overrun ......................................................... 3250 rpm
Turbo charger (2003T)
Boost pressure at full load / 3200 rpm, 20°C (68°F) ...... 100 – 120 kPa (14.5 – 17.4 psi)
Feed pump
Feed pressure at 2500 rpm .......................................... 0.65 – 0.85 kp/cm
2
(9.20 – 12.10 psi)
Electrical system
Battery voltage............................................................. 12V
Battery capacity........................................................... Max. 70 Ah
Starter motor output 2001 ............................................ 0.8 kW (1.1 Hp)
Starter motor output 2002 and 2003 ............................. 1.4 kW (1.9 Hp)
Alternator output, voltage/current ................................. 14V/50A
output ....................................................................... 700 W
Electrolyte spec. gravity:
Fully loaded battery .................................................. 1.275 – 1.285
To be charged at ...................................................... 1.230
Cooling system
Thermostat (sea water cooling) .................................... Wax thermostat
Starts opening at ...................................................... 60± 2°C (140 ± 4°F)
Fully open at............................................................. 75°C (165°F)
With fresch water cooling (2002, 2003, 2003T)
Starts opening at ...................................................... 74±1°C (± 2°F)
Fully open at............................................................. 87°C (189°F)
Fresh-water system, volume 2002 ............................... 4.0 L (4.2 US qts)
2003 ............................... 5.5 L (5.8 US qts)
2003T ............................. 7.0 L (7.4 US qts)
Wear Tolerances
Cylinders .................................................................... To be bored at 0.25 mm (0.00984 in.) wear.
Crankshaft
Main- and big-end journals:
Permitted out of round.................................................. 0.06 mm (0.00236 in.)
Permitted taper ............................................................ 0.05 mm (0.00197 in.)
Max. axial clearance on crankshaft .............................. 0.40 mm (0.01575 in.)
Camshaft
Bearing journals, permitted out of round ....................... 0.03 mm (0.00118 in.)
Max. clearance between camshaft and bushings ......... 0.15 mm (0.00590 in.)
Valves
Max. clearance between valve stem and valve guide ... 0.15 mm (0.00590 in.)
Min. thickness of valve disc edge ................................ 1.5 mm (0.05906 in.)
Tightening torques
Main bearing bolts, 1st tightening ................................. 20 Nm (14.7 ft. lbs.)
2nd tightening ................................ 60 Nm (44.2 ft. lbs.)
Big-end bearing bolts, 1st tightening ............................ 25 Nm (18 ft. lbs.)
2nd tightening ........................... 70 Nm (53 ft. lbs.)
Flywheel housing bolts ................................................. 25 Nm (18 ft. lbs.)
Flywheel bolts .............................................................. 65 Nm (47.9 ft. lbs.)
Cylinder head bolts, 1st tightening ............................... 20 Nm (14.7 ft. lbs.)
2nd tightening .............................. 70 Nm (51.6 ft. lbs.)
Rocker arm bridge ........................................................ 25 Nm (18.4 ft. lbs.)
Fuel injection pumps .................................................... 25 Nm (18.4 ft. lbs.)
Pulley .......................................................................... 40 Nm (29.5 ft. lbs.)
Injectors ....................................................................... 20 Nm (14.7 ft. lbs.)
Technical data
Vista de página 14
1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 47 48

Comentários a estes Manuais

Sem comentários